LMR 600 Cable
The LMR 600 cable is one of the many low-loss coaxial cables we carry at Allied Wire and Cable. This cable features a bare copper tube inner conductor and an aluminum tape outer conductor. This outer conductor enables the tightest bend radius of any cable of similar size and performance. It also features a foam PE dielectric and a tinned copper braid. The LMR 600 is designed for outdoor exposure, is UV resistant, and has a life expectancy of over 20 years.
21 items
-
EZ-600-716F$0.00 /
- Approx LBS/MFT: 158.00
- Connector Type: Straight Jack
- Contact Attach (Inner): Spring Finger
-
EZ-600-716M-RA-X$0.00 /
- Approx LBS/MFT: 462.00
- Connector Type: Right Angle
- Contact Attach (Inner): Spring Finger
-
EZ-600-716M-X$0.00 / 1000 FT
- Approx LBS/MFT: 209.00
- Connector Type: Straight Plug
- Contact Attach (Inner): Spring Finger
-
EZ-600-78EIA$0.00 /
- Approx LBS/MFT: 873.00
- Connector Type: Flange
- Contact Attach (Inner): Spring Finger
-
EZ-600-NF-X$0.00 /
- Approx LBS/MFT: 90.00
- Connector Type: Straight Jack
- Contact Attach (Inner): Spring Finger
-
EZ-600-NMH-RA-X$0.00 /
- Approx LBS/MFT: 224.00
- Connector Type: Right Angle
- Contact Attach (Inner): Spring Finger
-
EZ-600-NMK$0.00 /
- Approx LBS/MFT: 164.00
- Connector Type: Straight Plug
- Contact Attach (Inner): Spring Finger
-
EZ-600-TF-RP$0.00 /
- Approx LBS/MFT: 100.00
- Connector Type: Reverse Polarity
- Contact Attach (Inner): Spring Finger
LMR 600 connectors are specifically designed for LMR-600 cable in a large variety of common interface types. Available options include 7/8 EIA, 7-16 DIN Female, N Female, N Male, UHF Male and more. LMR-600 connectors are offered in a wide selection of connector types, including flange, straight jack, right angle and reverse polarity. LMR 600 coax connectors can be found with either a solder or non-solder center pin, and utilize a crimp outer attachment in standard hex crimp sizes.
LMR 600 Coax Cable Specifications
LMR 600 Construction:
- Inner Conductor: Solid Bare Copper Coated Aluminum
- Dielectric: Foam PE (Polyethylene)
- Outer Conductor: Aluminum Tape
- Outer Braid: Tinned Copper
LMR 600 Ratings:
- Temperature:
- Installation: -40°C to 85°C
- Storage: -70°C to 85°C
- Operating: -40°C to 85°C
- The LMR 600 diameter ratios and dielectric constant help determine the characteristic impedance. LMR 600 cable is 50-ohm coax.
- RF Shielding: 50 dB greater than typical single shielded coax (40 dB) - multi-ply bonded foil outer conductor rated conservatively at >90 dB
LMR 600 Applications:
- Jumper assemblies in wireless communications systems
- Short antenna feeder runs
- LMR 600 Coax Cable may be used in any application (ex. WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, Mobile Antennas) requiring easily-routed, low-loss RF cable
LMR 600 Standard Connectors:
- EZ-600-NMC-2-D
- EZ-600-NMH-2
- EZ-600-NMH-RA-X
- EZ-600-TM-X
- TC-600-NMC
- View more LMR600 connectors here
Construction of LMR 600 Coax Connectors:
- Description: Flange, Straight Jack, Straight Plug, Right Angle, Bulkhead Jack or Reverse Polarity (see part specs for full details)
- Inner Contact Attach: Spring Finger or Solder (see part specs for full details)
- Outer Contact Attach: Crimp or Clamp (see part specs for full details)
- See chart below and individual LMR 600 Coax Connector part specs for more info.